Pair of replacement filters for PowerCap® Infinity®. Filters should be checked, maintained and replaced regularly to ensure the unit performs correctly. The length of a filters life depends on working application.

About the filters

• These filters are high efficiency particulate types supplied in pairs.
• They will filter most particulate matter such as dust, spores, mist and fumes.
• They will not filter gases, vapours or toxic substances

Scott Pro 2000 CF 32 A2B2E2K2-Hg-P3 & filter for Organic, inorganic and acid gases and vapours as well as ammonia and organic ammonia derivatives as well as mercury and its compounds and ozone, solid and liquid, radioactive and toxic particles, plus microorganisms, e.g. bacteria and viruses.

Replacement patented ‘press to check’ filters for SHA112

FIT IT!
Don the Mask - Put the straps and harness over your head and pull the straps to a suitably tight and comfortable fit.

PRESS IT!
PressToCheck™ - Press the front and backs of both filter covers together to stop air from entering through the filters.

CHECK IT!
Inhale - No air should come through the mask. Adjust the mask and repeat until it doesn't. Release when seal is made.

Pre-Filters for the PowerCap® Infinity® PAPR - Pack of 100 (No covers)

Pre-filters (No covers) for the PowerCap® Infinity®. It is recomended that pre-filters are changed daily before use.

Only use genuine PowerCap® Infinity® filters supplied in pairs from JSP Ltd or its distributors. Always replace both filters simultaneously. NEVER use compressed air on the filters. This will seriously limit protection.

PowerCap® Infinity® delivers TH3 protection with a Nominal Protection Factor of 500 (UK APF 40). TH3 is the highest possible rating in the EN 12941:1998 + A2:2008 standard.

JSP Force8 PressToCheck ABEK1P3 Filter

Cover compatible with A2P and ABEK1 filters, to be purchased when using more than just the P3 filter

• Auto-darkening filter for most types of arc welding
• Designed for 3M™ Speedglas™ Welding Helmet Series 9100
• Variable dark shades 5, 8 and 9 through 13
• Light shade 3
• Viewing area: 54 mm x 107 mm
• Delay function sets the dark-to-light opening time
• Switching time (light-dark) of 0.1 ms
• The sensitivity of arc detection can be adjusted for unsurpassed switching reliability
• Tack welding comfort mode help minimize eye strain during extended tack welding applications

3M™ Speedglas™ Auto-darkening Filter 9100X, 500015 is designed for use with 3M™ Speedglas™ Welding Helmet Series 9100. Our filter features dark shades 5, 8, 9 to 13, a switching time (light-dark) of 0.1 ms, and a viewing area of 54 mm x 107 mm.

For an auto-darkening filter with seven variable dark shades (5, 8 and 9-13) for most types of arc welding, get 3M™ Speedglas™ Auto-darkening Filter 9100X, 500015. It has a viewing area of 54 mm x 107 mm and is made for the professional welder. Our 3M™ Speedglas™ Welding Filter 9100 Series features uniform shading and minimal distortion across the entire filter viewing area. The delay function sets the dark-to-light opening time, and it’s possible to lock-in any shade, e.g. in light state 3 when grinding. It has a switching time (light-dark) of 0.1 ms, and the sensitivity of the arc detection can be adjusted for reliable switching. Tack welding comfort mode also helps minimise eye strain during extended tack welding applications.

• Regular replacement of the Adflo™ pre-filter extends the life of the particle filter, saving money while also increasing the battery run-time
• Inspect your pre-filter regularly for any damage, clogging or breakthrough
• Do not attempt to clean the pre-filter
• For use with the 3M™ Adflo™ Powered Air Respirator
• 5 per pack

3M™ Adflo™ Prefilter, 836010, is a replacement prefilter designed for use with 3M™ Adflo™ Powered Air Respirator. There are 5 in each pack.

Increase the battery run-time and reduce operating costs when using 3M™ Adflo™ Powered Air Respirator with 3M™ Adflo™ Prefilter, 836010. Our prefilter captures large particles that may otherwise clog the particle filter, reducing operating costs by extending its life. It can also increase battery life efficiency. It comes as a pack of five and must be installed and used according to the user instructions. To increase service life, make it a habit to check your equipment regularly.

• Replacement particle filter P SL for 3M™ Adflo™ Powered Air Respirator
• Simple to install and must always be used to maintain service life of your respirator
• Replace when particle filter indicator becomes red, when the battery operating time becomes too short or when "fully loaded" filter triggers low airflow alarm
• To increase service life, make it a habit to check your equipment regularly
• 2 per pack

3M™ Adflo Particle Filter, 837012, is designed to replace worn or damaged particle filters in 3M™ Adflo™ Powered Air Respirator. There are two in each pack.

Ensure optimum performance from your 3M™ Adflo™ Powered Air Respirator, with 3M™ Adflo Particle Filter, 837012. Our replacement particle filter is simple to install and must always be used. It should be replaced when the particle filter indicator becomes red, the battery operating time becomes too short or when a "fully loaded" filter triggers a low airflow alarm. There are two in each pack. To increase service life, make it a habit to check your equipment regularly.

6059 A1 filters protect against vapours, acid gases and ammonia. For 6000, 7000 and 7500 Series half masks and full face masks.

• Standard: EN1438
• Approval: CE Marked
• Half Masks: Class 1 Filters – 10xWEL or 1000ppm; Class 2 Filters – 10xWEL or 5000ppm
• Full Masks: Class 1 Filters – 20xWEL or 1000ppm; Class 2 Filters – 20xWEL or 5000ppm

3M 6038 P3R (nuisance level organic vapour and acid gas and hydrogen flouride). Encapsulated Particulate Filters.

• Ideal for wet conditions
• Hazard is contained within filter media, protected by plastic case avoiding risk of skin contamination on removal of filter.
• Easy clean surface

Standard: EN143
Approval: CE marked
Maximum use concentration
When used with half masks: 20xWEL• Hydrogen Flouride: 10xWEL
When used with Full face masks: 40xWEL, Hydrogen Flouride up to 30 ppm Below WEL for gases and vapours
•Workplace Exposure Limit

5935 P3R Particulate filters for use with 3M? Gas and Vapour Filters. Use in combination with 3M? 6000 Series Gas and Vapour Filters with a 3M? 501 Filter Retainer for combined gas/vapour and particulate protection. Extremely lightweight. Standard: EN143, Approval: CE marked.